Makita LS1040F Dokumentacja

INSTRUCTION MANUALWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.www.makitatools.comC

10• After changing the miter angle, always secure the turnbase by tightening the grip firmly.Adjusting the bevel angleTo adjust the bevel angle, loose

11WARNING:• NEVER use tool without a fully operative switch trigger.Any tool with an inoperative switch is HIGHLYDANGEROUS and must be repaired before

12To remove the blade, use the socket wrench to loosen thehex bolt holding the center cover by turning it counterclock-wise. Raise the blade guard and

13Dust bagThe use of the dust bag makes cutting operations clean anddust collection easy. To attach the dust bag, fit it onto thedust nozzle.When the

14CAUTION:• When performing left bevel cuts, flip the fence over to theleft position as shown in the figure. Otherwise, it willcontact the blade or a

15the projection may stop at an angle. In this case, turn the viseknob back counterclockwise until the screw is released,before turning again gently c

16• Do not apply excessive pressure on the handle whencutting. Too much force may result in overload of themotor and/or decreased cutting efficiency.

17• During a bevel cut, it may create a condition whereby thepiece cut off will come to rest against the side of theblade. If the blade is raised whil

18There are crown and cove molding joints which aremade to fit “Inside” 90° corners ((1) and (2) in Fig. A) and“Outside” 90° corners ((3) and (4) in F

19EN0002-1Compound Miter Saw Miter and Bevel Angle Settings00003152˚38˚CeilingWallWall to Crown Molding Angle: 52/38 degreesWall Angle (deg.)Bevel Ang

2SPECIFICATIONSBlade diameter : ... 255 mm (10”)Hole diamet

20 EN0003-1Compound Miter Saw Miter and Bevel Angle Settings00003245˚45˚CeilingWallWall to Crown Molding Angle: 45 degreesWall Angle (deg.)Bevel Angle

21Crown molding stoppers (optional accessories) alloweasier cuts of crown molding without tilting the sawblade. Install them on the base as shown in t

22CAUTION:• Use straight wood of even thickness as the wood facing.• Use screws to attach the wood facing to the guide fence.The screws should be inst

23Carrying toolMake sure that the tool is unplugged. Secure the blade at 0°bevel angle and the turn base at right miter angle fully. Lowerthe handle f

24Lower the handle fully and lock it in the lowered positionby pushing in the stopper pin. Square the side of theblade with the face of the guide fenc

25(2) 45° bevel angleAdjust the 45° bevel angle only after performing 0°bevel angle adjustment. To adjust left 45° bevelangle, loosen the lever and ti

26ACCESSORIESCAUTION:• These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other acc

Memo27

Memo28

29First-ClassPostageRequiredPost Office willnot deliverwithout properpostage.Makita U.S.A., Inc.14930 Northam StreetLa Mirada, CA 90638-5753FoldCut

35.DON’T USE IN DANGEROUS ENVIRON-MENT. Don’t use power tools in damp orwet locations, or expose them to rain.Keep work area well lighted. Don’t useto

301. This product was purchased from:Home CenterHardware/Lumber StoreTool DistributorIndustrial SupplyConstruction SupplyOther ( )

31FACTORY SERVICE CENTERS1-800-4-MAKITARETAIN THIS PORTION FOR YOUR RECORDSARIZONA3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850CALIFOR

WARNINGSome dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Calif

4VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.)be sure the voltage supplied is the same as that specified on

59.Do not use the tool in the presence offlammable liquids or gases.10.Check the blade carefully for cracks ordamage before operation. Replacecracked

6SAVE THESE INSTRUCTIONSWARNING:MISUSE or failure to follow the safety rules stated in thisinstruction manual may cause serious personal injury.

7INSTALLATIONInstalling auxiliary plateInstalling the auxiliary plate using the notch in the tool’s baseand secure it by tightening the hex bolt.Bench

8FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off andunplugged before adjusting or checking function on thetool.Blade guar

9Kerf boardThis tool is provided with the kerf board in the turn base tominimize tearing on the exit side of a cut. If the kerf groovehas not yet been