Makita LS1013F Instrukcja Użytkownika

INSTRUCTION MANUALWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.www.makitatools.comS

10Stopper armThe lower limit position of the blade can be easily adjustedwith the stopper arm. To adjust it, move the stopper arm inthe direction of t

11Switch actionCAUTION:• Before plugging in the tool, always check to see that theswitch trigger actuates properly and returns to the “OFF”position wh

12Lighting up the lampsCAUTION:• This is not a rainproof light. Do not wash the light inwater or use it in a rain or a wet area. Such a conductcan cau

13Installing or removing saw bladeCAUTION:• Always be sure that the tool is switched off andunplugged before installing or removing the blade.• Use on

14To install the blade, mount it carefully onto the spindle, mak-ing sure that the direction of the arrow on the surface of theblade matches the direc

15be destroyed. PERSONAL INJURY MAY ALSORESULT. Also, after a cutting operation, DO NOT raisethe blade until the blade has come to a complete stop.CAU

16Vertical viseThe vertical vise can be installed in two positions on eitherthe left or right side of the guide fence or the base. Insert thevise rod

17CAUTION:• Always rotate the vise nut to the right fully when securingthe workpiece. Failure to do so may result in insufficientsecuring of the workp

181. Press cutting (cutting small workpieces)Workpieces up to 91 mm (3 - 5/8”) high and 70 mm (2 -3/4”) wide can be cut in the following way.Push the

19• Never loosen the knob which secures the carriage whilethe blade is rotating. This may cause serious injury.3. Miter cuttingRefer to the previously

2SPECIFICATIONSBlade diameter : ... 255 mm (10”)Hole diamet

20When performing compound cutting, refer to “Press cut-ting”, “Slide cutting”, “Miter cutting” and “Bevel cut”explanations.6. Cutting crown and cov

21Example:In the case of cutting 52/38° type crown molding forposition (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°LEFT.• Adjust and s

22Example:In the case of cutting 52/38° type crown molding forposition (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°RIGHT.• Adjust and

23EN0002-1Compound Miter Saw Miter and Bevel Angle Settings00003152˚38˚CeilingWallWall to Crown Molding Angle: 52/38 degreesWall Angle (deg.)Bevel Ang

24 EN0003-1Compound Miter Saw Miter and Bevel Angle Settings00003245˚45˚CeilingWallWall to Crown Molding Angle: 45 degreesWall Angle (deg.)Bevel Angle

25Crown molding stoppers (optional accessories) alloweasier cuts of crown molding without tilting the sawblade. Install them on the base as shown in t

267. Cutting aluminum extrusionWhen securing aluminum extrusions, use spacer blocksor pieces of scrap as shown in the figure to preventdeformation of

27Carry the tool by holding both sides of the tool base asshown in the figure. If you remove the holders, dust bag, etc.,you can carry the tool more e

28Make sure that the pointer points to 0° on the miterscale. If the pointer does not point to 0°, loosen thescrew which secures the pointer and adjust

29Make sure that the two pointers on the arm point toeach 0° on the bevel scale on the arm holder. If theydo not point to 0°, loosen the screws which

35. DON’T USE IN DANGEROUS ENVIRON-MENT. Don’t use power tools in damp orwet locations, or expose them to rain.Keep work area well lighted. Don’t uset

30• Leave the florescent tube for a while immediately after ause of it and then replace it. If not. You may burnyourself.Remove screws, which secure L

31ACCESSORIESCAUTION:• These accessories or attachments are recommended foruse with your Makita tool specified in this manual. Theuse of any other acc

Memo32

33First-ClassPostageRequiredPost Office willnot deliverwithout properpostage.Makita U.S.A., Inc.14930 Northam StreetLa Mirada, CA 90638-5753FoldCut

341. This product was purchased from:Home CenterHardware/Lumber StoreTool DistributorIndustrial SupplyConstruction SupplyOther ( )

35FACTORY SERVICE CENTERS1-800-4-MAKITARETAIN THIS PORTION FOR YOUR RECORDSARIZONA3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850CALIFOR

WARNINGSome dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Calif

4VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet,etc.) be sure the voltage supplied is the same as that specified on

57. Unplug tool before changing blade or ser-vicing.8. To reduce the risk of injury, return car-riage to the full rear position after eachcrosscut ope

6INJURY as shown in the figure. ALWAYSuse vise to secure workpiece.30. Do not abuse cord. Never yank cord todisconnect it from the receptacle. Keepcor

7INSTALLATIONBench mountingWhen the tool is shipped, the handle is locked in the loweredposition by the stopper pin. Release the stopper pin by lower-

8If the see-through blade guard becomes dirty, or sawdustadheres to it in such a way that the blade is no longer easilyvisible, unplug the saw and cle

9First, unplug the tool. Loosen all the screws (2 each on leftand right) securing the kerf boards. Re-tighten them only tothe extent that the kerf boa